Wet felting products from wool for beginners. Felting Wet Felting Wet Fluff for Beginners Toys

Very ancient felting technique (folding or felting) received the second life in our time. With this simple technology, you can create a lot of useful and pretty things. The easiest thing is the process can be understood by the example. Fuling toys is a good opportunity to understand the process. There are several different techniques. Consider dry and wet fooling toys.

The word "dry" says that water will not be applied. Unlike other types of falothing, not wooing woolen raw materials is used here. This kind of needlework is worth using if you need to get volumetric things.

To obtain a very large volume, they use the basis of a synthetic winterizer, foam rubber, or something similar to any size and drape. Gradually covers the entire surface of the blank of raw materials. At the same time (at the same time) make it more dense and evenly with the help of needles.

Necessary materials and some dry felting techniques

For dry felting (felting), it is used not to be spinned woolen mass and special needles. The needles differ from ordinary sewing presence of jar on the end. These serifs and descend the fur. As a result, it turns out felt.

Natural Wool Color Palette:

It should be borne in mind that with improper use of the needle often break. The greater the needle number, it is thinner. If in the process of work it is seen that there are holes, it means you need to take a needle of the fond. Beginners usually use needles with a triangle cross section or an asterisk at the end. In the process of improvement, each master in accordance with its experience and preferences chooses needles. These tools can be diamond, tristar and crowns. There may be a cone-shaped or cylindrical form. There are other options, but they are rarely applied in practice. If you use several needles at once, then you will increase the speed of work. But a special holder is needed. It can be for different amounts of needles (starting with one needle).If there is no this device you can use an ordinary plug. The needle in the product is strictly vertically vertically (perpendicular to the product).

Needles for needlework

If you decide to apply Felting for your work, you should prepare other devices. For the separation of strands of wool useful combing comb. Puzzle will be needed to shake it. In the future, to speed up the felting work, you can try to apply a card reader. With it, you can quickly mix and comb woolen nurses. Since the needles can damage the fingers to work better to use thimbles.

You still need something to put something under the product during felting. If this is not done, then the needles will break about the hard surface. It is necessary to take a brush, foam sponge, hard felt or foamed polyethylene for lining under the workpiece.

Welding master class part 1

Welding master class part 2

Creating a toy by dry felting

For the manufacture of the toys, you will most likely need: scissors, a glue gun (or just adhesive), form for a roller (usually made from the foam rubber), sewing needles, for flexible products you need a wire to which felt is well supplied. Let's try to eat, such as a mouse.

Sleever is good for the basis of the product. These are sheep cleaned wool (without an arrangement). You can try to work with camel or dog wool.

It is clear that the felt toy will get the same color as the wool chosen for craft. We select the material of the desired color (or several colors).

We begin dry felting from wool both toys and any other crafts equally. You can create different things, and the actions will be the same

The stages of this process are as follows:

• We tear the right amount of wool.
• Twist your hands into a ball or cylindrik (or other necessary shape).
• Casting needle to the workpiece, fasten the product throughout the volume.
• Turn the product to evenly compact the product and align it.

First, a torso is done a mouse (cylindrik). It is gray. Compact. We highlight the belly of animals, for example, white. For this, a small piece of white wool gather in the right place. In the same way, I rolling your head, just roll the ball. Now put the spout. To do this, roll a small cone with hands. Sealing it, taper to the ball. Also create ears. Head is ready. We highlight the eyeball. In the right places stick the needle until two recesses are formed. Beads (or buttons) are wetting glue and (with a tweezers) glue in the eyeball. You can glue a bead on a nose mouse. If you need a mustache to make them from a fishing line or thin wire. Now you need a cinema wire. With it, legs, pens and tail are made. Wrap a wool wire. Rolling. We attach to the body. Mouse ready. Using these techniques, it is not very difficult to achieve the result.

Fly mouse

Wet felting

As can be seen from this phrase, water will be used. It should be remembered that woolen things for wetting give shrinkage. When using this method, it will be about twenty percent. So making patterns need to increase them on the appropriate value.

Toy patterns:

Beginning of work

To make a toy by the method of wet fake, of course it will need water (hot). It should be immediately noted that this method you can make toys and other crafts are flat (one-dimensional) or hollow inside (such as puppets).

By the way, the cavity of the finished product can be filled (for example, with a capacity) and the bulk thing will turn out. Soap will need. If you use an ordinary soap (baby), then it is pre-grated to be grate and soak in hot water. Liquid soap is permissible to pour directly on the wet blank. Since it will be necessary to work with a wet material, a smooth surface is to be covered with a glued. Top laying pipple polyethylene. The pattern should certainly be waterproof (a dense polyethylene is suitable).

Fly Koto - Slippers

How is the process of wet felting.

Prepare the wool of the desired colors in the required quantity, we turn directly to work. To make a toy, create a pattern (remember about shrinkage).

• Put the pattern on the prepared surface.
• Let's cover it with slices of wool. We put along and across, so that the strands overlap each other. Watch not to be properly. Dry wool blanks should be about finger (in thickness).
• Abundantly wet the warm soap solution. If we use liquid soap, then we water soap, and from above hot water.
• Smoothed circular movements (approximately 100 stroking). Where the wpina is felt there we repeat the wool. If the material goes beyond the template, wrap it inside.
• We cover the semi-finished product with a caprony cloth (or a bamboo rug, someone uses another sheet of poultry polyethylene). Watch the product and rolling on the table (even 100 times). You can pre-press a little excess water.
• Thus, the blank is flat and monophonic.

• How to make a double (with cavity inside) crawl? To do this, we put the template on top of it (it may be the same) and begin the wet fuel from the wool again. At the same time, it is necessary to avalize two blanks together in those places where it is required. If you need to select some places on the handy of other colors, then add where it is necessary to felt the wool to felting the desired colors. So that the colors do not blur the remaining surface (for example, a piece of polyethylene). It is possible to make individual felted parts, and then sprinkle to the main product.
• If the toy is ready, then you need to wash it from soap several times in cold water.
• The drying toy from wool on a flat surface at room temperature.
• Put the product (if necessary) woolen / sinteration.
• Ready.

Toy felting process creative. If you show a fantasy, you will get truly wonderful things that will please others.

Each craftswoman who is fond of needlework, tried to create toys. There are many techniques for performing such products. Among them was widely popular toys. This technique is also called polling or felting.

Dry felting technique

In ancient times from wool, carpets, flooring, clothes, hats. Now needlewomen are keen on the creation of decorative things, toys, decorations and souvenirs from the felt. In the process of ferrous fiber, the wool is twisted and form a dense lump, which in the hands of the valillats acquires the desired shape. The main thing is to take into account that the amount of wool originally taken is 2-3 times the amount of wool. Therefore, creating toys in the technique of dry felting, you need to stock up the necessary amount of material.

If irregularities were formed in the product, they can be treated, taking additional pieces of wool. Often toys dry filling create from several parts, which are made separately, and then compound by parceling of one element to another with small pieces of wool.

Tools for felting

Such a kind of needlework, like dry rolling of toys, does not require special equipment. In the initial set, it is enough to have needles of different diameters and sections. You will need a synthetic procession from which the work on felting begins. It is inexpensive, so for the manufacture of large toys is taken as the basis of the future product. It still needs wool for the upper layer, which turns around the prepared part of the synthet board and is supplied to the base.

Many use such a tool as a needle holder. It is a plastic or wooden handle with holes that holds several needles at once. The needle holder speeds up the work process, helping to capture most of the area.

Dry felting toys cannot be performed on a solid surface. The needle, which pouches the product through, from hitting the table can break. To avoid this, you need a special mat for polling, brush or foam sponge.

Read more about Iglags for felting

The entire process of filing is performed by the needles of different sizes. It does not have a toe, with its shape resembles a poker and can be up to 13 cm long. The needles are classified by number and shape of the section. The thickness is marked №32-№36 and are used at the beginning of work, but they leave after themselves major punctures in the product. Therefore, the details complicated, the needle is changed to the middle number 38. With its help, the recesses are formed, the main work and the toy finish are performed. The needle number 40 grind the product and modify the decor. The needle should be changed when it is bad enters the detail of the crafts. If you do such a needlework, like dry felting toys, there will be three needles of different diameters with a triangular cross section for beginners. This form is most common and can be used at all stages of work, only the needle number changes. There are those who have a star cross section. They are used to polish the product. The crown needle helps to accumulate decorative elements without deforming them. There is still an needle of the reverse section, which dies out the inner layers of the base. It is used by professional masters to give a toy natural color from different shades.

Processing needle

In the process of rolling, the needle is continuously stuck in a wool lump, penetrating deep into and capturing fibers. At the same time, the patches are twisted and drunk until the billet acquires sufficient density.

Filler needles are very sharp, so you need to work extremely carefully. During felting, you should not be distracted, otherwise you risk yourself to seriously impass. When working with a needle, the flammable product should not be kept on weight, it is necessary to put it on a special fixture that cannot be dumping. When the needle is running, it is impossible to tilt and stitch, and you need to keep them perpendicular to the craft, as they are very brittle.

Variety of wool

Toys in dry felting technique are performed from sheep wool. The wool of the Australian and New Zealand Merinosov, which has its differences is especially appreciated.

Male and toys, which are obtained with shaggy wool, are created from the coarse sheep wool.

Whiten, which can be easily colored at home, is called a selection. It is used as a basis or to create a light background.

Weeping is called sheep wool from small hairs left after grasia. It can be applied when stuffing toys.

Sliver is the cheapest unpainted wool. It is used as a filler to which the main layer of the desired color is supplied.

Falltonal applied to finishing products.

Also toys with dry felting are performed from camel and goat wool.

How to connect the details

If you have not worked with wool, and you are interested in dry felting toys, it is important for beginners to know how to connect separate parts with each other. After you put the details of the toy separately, the main thing is to attach them to the body correctly. The place of the council should not be so tight as all the product. Working the needle, you need to bypass these places, leaving them loose. The wool of the combined part should fall deeply and inside firmly secured. We rush the element to the tank pins and find the right position. After that, the thick needle refuel the wool parts inside the calf, achieving a strong connection. After making sure that the item sits quite tightly, align the surface and closed the seam with separate beams of medium needle wool. Having embedded the connection site, they can be pulled out with a thin needle.

How to shake the product

The toy, sleeping from wool, can be flipped in two ways:

Using a reverse needle;

By parving individual wool bundles.

The craftsmen mostly flashes the ready-made toy with all the attached details. Casting back needle in the Taurus, pull out the fibers of the wool outward. Try to make punctures close to each other, so that the toy has a thick fur without proper. Depending on the size of the product, several hours can leave for dissolve. After completing the work, the fur can model modelily, giving the toy a finished look.

The second way to dissolve implies the external parcel on the handicraft of thin strands of wool. Starting from the bottom of the toy, we apply the middle of the strand to the calf and we attach the needle number 38. Thus, we increase the wool in a circle of the product. Then omit all the strands down. The following beams are supplied by retreating up from the bottom row 1 cm. The work will be over when you flush the entire surface scheduled for the wool.

Mix colors

If you wish to make toys with your own hands, dry felting makes it possible to make a little animal as possible and alive. Give the toy natural color will help mix six different shades. You can do this as at the beginning of work, creating details of the future product, and by picking a wool of different colors.

If you choose the first method, a lump of the wool of one color is taken as the basis and falls slightly, then turns around the color of the future skin of the animal and is supplied. The color will be mixed at the stage of working with a reverse needle. The needle will release wool inside, and partially flush the outer layer. During the process, the toy will acquire an interesting close to the living hue. The main thing is to pick up the colors close to the animal wool.

To create strips, a method of dissolving by falling is suitable. Only in this case you need to build a wool, alternately changing the color of the strand in the distance you defined. This method is like for toys with long wool. To create short-haired little animals, the strands need to be tight throughout its length, creating a schematic layout on the Taurus. Then flush the reverse needle.

Dry felting toys: master class of fooling toys on frame

The felting process is a very exciting occupation. It calms down and makes it possible to reflect and dream.

Consider a small MK for beginners. Dry felting toys can be performed using a frame. Create a wool doll. To work, it will be necessary on which cut pieces with a length of 8 and 14 cm, wool for filling different colors - it depends on the invented image. The needles of the triangular section No. 38 for the initial stage, No. 40 for full seal, and star №40 for grinding, sponge for felting.

To create a frame to fold in half a segment of a wire of 14 cm long, it will serve as legs. In the loop, impose a second segment for hands. Twist the wire several times by forming a torso. Next Leave 5 cm wire free for legs. Depending on what position the pupa will take, bend the framework. It can be bends knee, stop, elbows and hands. Wake up the whole frame of the product by strands, gradually fasten it with a needle for felting. In the area of \u200b\u200bthe torso and brushes, make a little more wool, increasing the volume.

To make a head, you need to form a woolen ball and put it with a needle, seeking a diameter of no more than 2 cm. Then tear off the long and wide strand, wrap it with the head of the doll, appropriate, and secure a small block by creating a neck. Sweating wool distribute in front and rear of the body, attach your head and stretch strands to the frame.

Next you need to put on the doll dress. To do this, take the wool of the desired color and start sprinkling strands vertically to the waist line, creating a skirt. Plugging the strands around the entire body of the pupa, cut the ends, so that the lower edge of the skirt was smooth. To form the top, wind the doll torso strands, fixing their needle number 40.

In the same way, you can make a pupa of ballet or sleeves. The handles can be bent and placed in the palms of the flower. Finish the image by creating an appropriate hairstyle.

Choosing dry felting toys as needlework, you should know that this work is very painstaking and requires perfection and patience.

Felt (eng.) - [SUB.] Felt, felt; [Glazh.] Wool wool, shoot down felt

I think, first, not to prevent you know the answer to the most important question - why the wool falls. It's all about her structure! Remember, not so long ago on TV circled advertising shampoo making hair smooth and silky? Then close-up showed a dumb swallowing hair. So, sheep wool in normal condition looks about the same \u003d)

Comparison of human hair and sheep wool. Many differences?

Because of such a "bundle", human hair can even form chopencies, "fall". But that for our hair is not good, for felting - good. It is the structure of sheep wool that allows you to create wonderful toys, clothes, boots, carpets and more.

Naturally, not only sheep wool is suitable for filling. You can use alpaca, camel, lama and yak, and cashmere, anagora and mohair.

Folding (Felding, Fillerization) is the process of creating various products from an indiscriminate wool by clutching and interlacing its fibers in various ways.

There are many different types of felting - dry, wet, nuno felt, felting knitted things. Below I will consider basic techniques

Basic techniques of dry felting for beginners

First of all, we will get acquainted with the technique of dry felting wool. Although she appeared much later than wet foolishness, but currently conquers increasingly popularity. With the help of an ordinary needle, you can create truly unique creations! Here, take a look at work of famous masters

I want to warn that this kind of creativity is not suitable for children up to 10 years and lovers to create a TV (although I do it). If you are too distracted, you can pierce your finger through - the needles are very sharp, and the notches are well torn the skin.

Briefly describe the process:

The wool layout is impregnated with a hot soap solution, then stroke and work in various directions, gradually enhancing pressure. To facilitate work in the initial stages, the vibratingrene machine is often used. Get a cloth - felt.

Council. Making patterns of the desired product, consider that when the wet is wool, the wool sees interest on 30-40 percent

Wet felting technique

This step-by-step description of the wet fooling technique will help beginners to penetrate (and, I hope, I will think of trying to try and enjoy) process \u003d)

It will take:

• imperount to wool
• bubble wrap,
• bamboo napkin,
• soap,
• warm water.

1. Separate from the woolen ribbon the same shoes of the wool with a length of centimeters 8. lay them on a bubble film in one direction, a little overlapping each other. Similarly, lay out 3-4 layers, wool fibers in each of which are perpendicular to the previous one.
   
   
2. The last layer can be applied with a pattern of woolen thread scraps, shoes of wool, etc.
   
   
3. We prepare a soap solution. To do this, in warm water, we dissolve soap (there is a special soap for wet fuel, carefully related to the skin of the hands, but you can use the children's, liquid soap or even a means for washing the dishes) - which is at hand. Welcome our workpiece and cover with a grid or bubble film.
   
   
   Soft circular movements stroke wool in all directions. Gradually enhance pressure. This stage can be finished when individual fibers will stop separating from our web.
4. We put the workpiece together with the film on the bamboo napkin and we turn into a tight roll. Watch this design in a towel - it will help remove excess water. Kating there and here once a hundred. Then we turn around, turn the cloth 90 degrees and make a roll again.
   
   
5. When you bother the cloth will decrease percentage of 25-30. Ready rinse canvas in warm water and leave dry. Do not ridge - only slightly squeeze to remove part of the water.
   

Thus make carpets, paintings, clothing, bags, decorations and accessories.
Visptious about wet felting:

Washing in a washing machine

One of the techniques of wet fuel from wool can be attributed to felting in a washing machine. It almost does not require physical effort and can be carried out in two ways:

1. Using a form for a roller
   Volumetric forms are covered with wool, fixed by a trap and send into a washing machine.

• Flawing knitted products
  Currently, you can find a special yarn for felting. Crochet or knitting you knit the product, percentage by 30 (to know the exact shrinkage lay the trial sample and the compression is calculated on the width and length) more required and either send to the washing machine or manually. It looks very interesting, isn't it? And it's easier to wet fooling, as for me so.

That's all!

So, we considered the basic felting techniques from wool - the most interesting creative process. If you are a beginner pill and some moments you do not understand - feel free to ask questions!

Do not be afraid to experiment!

There are many different types of needlework, among which you can always choose what is most likely. There are no sense advice here, since each creative person is looking for his direction. Take, for example, felting. This unfamiliar kind of needlework is actually a good opportunity to learn how to do a wide variety of healthy things.

Raw foil - or felting is a useful and interesting hobby, which can be practiced at home, plus, this is a good way to earn. The technology allows you to produce from felt not only the usual woven, but also toys, paintings, bags and even jewelry. In our article - Wool layout technique, MK on making toys, useful video at the end of the article.

The good enough felting, so it is to learn how the child can and adult. Even those who do not seem to have any abilities for creativity, begin to make the most incredible things. But first, you need to learn this art and see several master classes.

Wet felting came to us from those edges where sheeping is developed. People there have long made their clothes by soaking and felting animal wool. By the way, one of the advantages of this direction can be called therapeutic feature - this is a good way to massaging your fingers.

The main task of the master class is not just learning, but the possibility of making a practical felon.

Before starting work, you need a whole list of materials and remedies:

Well, the most important thing that should be on the table is wool, scissors, needles with jazbins for hazard dumping, marker and stationery knife.

Topics who is engaged in needlework on an ongoing basisMake sure the grinders (vibration). With it, you can speed up the process several times.

Frequent use of the finished product will require well fasten all the details. For these purposes, impregnation is used in the form of acrylic varnish, wallpaper glue or cellulose in granules.

Gallery: Wet felting products from wool (25 photos)

Wet Fluff: Master Class

So, we dealt with the necessary devices and tools. Now you can start learning.

The easiest and necessary of the large list of products is an ordinary ball. It seems to be nothing complicated in this, however, even among the masters themselves there are disagreements on the method of rolling the ball. The easiest way is to: take a few pieces of woolen scum to smire them, moisten in soap solution and roll.

The second method is more complicated:

Consider using wet fuse from wool, master class on color creation.

1. On the film with bubbles laid out wool layers. Woolen pieces pull hands, overlapping several layers on each other. One layer is laid out along - another across, and so on. They should be affixed at each other evenly.
2. The naturalness of the flower is achieved by imposing on the first aligned layer of the second with a different color, but by shadowing similar to it.
3. From the layer of the second color, it is accomplished by twisting fibers in the thread.
4. The flower is covered with a mesh, wetted from above soapy water and pressed his palms.
5. After that, the grid ride the rolling pin in different directions.
6. As soon as the hairs stop separating apart from each other, the semi-finished product is removed and continue to fill their hands.
7. Wash the product with running water and scissors to fill irregularities.
8. It is once again a little ride a rolling pin and put on a glass or a vase, giving a flower shape.

From such a flower you can make a brook, or just decorate the interior to them. Such a master class will even come true for learning children aged 11-12 years.

Wet felting paintings

An interesting direction in this work is to felting paintings. Wool with various shades of colors Beautifully overflows and the result obtained looks very good. The master class of creating pictures consists of the following steps:

The main plot is formed both dry and wet. If flowers are involved in the picture, then:

• buds, leaves, petals are formed from pieces;
• for stems and branches, harness is twisted;
• all this is placed according to the plot and is covered with a grid;
• through the mesh, the cloth is wetted with water with soap and first strokes lightly;
• gradually the pressure increases;
• if the probability of displacement disappear disappeared, the grid is removed and the felting begins.

Folding implies not only rolling the rolling pin, but also the execution of manipulations of the same as with the test. When everything is ready, the picture is clean, it is dried and decorated with a frame. Dry best straightening on some board.

Toy manufacturing technique Always was a dry method. However, for beginners, especially trying the wet method, it will be easier to eat using a master class with soapy water. Consider how to make toys on the example of chanterelles. It will take all the same and plus to work to work: a needle with a thread, a large towel, polyethylene, eyes for animals.

Getting to work:

To the lesson's toy looks different, it is stretched, for example, on a glass and dried. The dried figure is sewn.

Valya clothing items

On the Internet a lot of master classes In the manufacture of all kinds of items. Wool products occupy no last place. Using felting technique, experienced masters make trendy handbags, boots, socks, mittens, all sorts of decorations.

Quite a simple way of making clothes, you can call felting socks. If anyone had to knit them, it will be easier:

This simple way is suitable even novice needlewomen.

What you need to know using felting technique

Working in this industry, do not forget that there are necessary requirements, about which you can not forget:

Elizabeth Rumyantsev

For diligence and art there is nothing impracticable.

Folding (Felding, Filing) belongs to a long time of needlework. Water wool products created by craftswomen from all over the country diverge in stores like hot cakes. Step-by-step felting from wool for beginners allows you to make unique items. Felting is the creation of crafts from wool with the help of the clutch and interlacing the fibers by several methods. The modern art of filing includes: wet, dry fooling, nanofilting.

Wool felting features

Before starting to step by step out of wool for beginners, you need to find out what will be needed for this exciting artistic process. The first thing you need to order is any natural wool. The material is available on the shelves of specialized department stores and in online stores. What raw materials and tools are better to purchase?

Crafts are often made of rude sheep wool or camel. As a basis for the product, it is recommended to buy a slurry - combustible sheep wool without an arrangement. A packing, for example, a cat's toys or slippers often becomes the wholeness, and Merinos comes to the decoration of items. Folding it is impossible to make a needle. Special tools are of different sizes (thin, thick and medium), various sections (crown, triangular, star). So, we purchase a set for felting from wool for beginners and go to master classes.

Master classes for rolling out of wool with a step-by-step description of the work

This section is for those beginning masters who want to try their strength in polling. We learn what is the dry method of felting, wet felting and felting with a washing machine. A detailed study of master classes will make it possible to produce products of absolutely any level of complexity: from small decorative parts to clothing items.

Dry felting technique for beginners

For step-by-step fuel from wool for beginners with a dry way, it is necessary for indiscriminate wool (optimal option - cardochesis) and special needles with jar. Dry felting is a confusion of the fiber material among themselves, as a result of which they are transformed into felt. Welding this method is carried out using a needle with a triangular and star cross section. We prepare wool, needles for filing, a thick piece of foam rubber and go to practice. Further:

1. Material put on the foam rubber, we tweak with a needle. The base of the crafts is sometimes made of syntheps, covering it from above the coat.
2. When working with needles, it is worth a maximum of accuracy, because they are sharp. The needle must be kept perpendicular to the craft. The process of creating any item from felt begins with the use of a thick needle that gradually changes to thin.
3. The flaws in the form of irregularities on the artistic subject are smoothed using additional raw materials.
4. Dry Felding is a volumetric souvenirs (badges, key rings), accessories (wallet, bag, books for books), coat of felted wool, caps, boots, and so on.

Wet felting

Wet felting from wool on marla is performed using a warm soap solution (some replace it with liquid soap). For gauze, according to the selected diagram, the material is laid sicks. The mixture is done like this: weching on the grater a pair of soap pieces, chips fill with two liters of hot water, mix well, we are waiting for 2 hours until the solution becomes thick. Next, stages:

1. Ellipped the cape on the floor or other comfortable smooth surface. We put marlu on top.
2. Then lay out the basis, on it the background and selected pattern.
3. Threads are superimposed by custody, stripes. Watch that there are no holes in the canvase, and the material layers lay perpendicularly. Their thickness should be the same.
4. When the material is already decomposed in accordance with the drawing, you need to sprinkle with water, cover with a cloth from Capron and lubricate with soap solution. Excess liquid we remove the paper napkin.
5. The next stage is a felting of paintings, panels, toys or jewelry (brooch, beads). Wet feling of any product is to rub the fabric manually in different directions.

Fooling in a washing machine

Felting with the use of washer refers to the easiest and simple method of creating things from felted wool. We will use dense forms for slaughterings, which are crushed by hairs of wool and put in a golf from Capron (or part of the usual headband without holes, arrows). We proceed directly to the creation of a felted craft:

1. The workpiece must be put in a bag for washing and placed in a washing machine. We embarrass into a special recess means for washing woolen things, set the cycle without soaking and drying. To achieve an optimal result, we put the temperature of 50 degrees.
2. When the car finishes the washing process, we take out our ready-made sawder. If you decide to use the shape for the collapse, it is better to extract it from the workpiece with scissors.

Where to buy and how many sets and wool for felting

For each beginner needlewoman, which decided to try himself in the art of filing, it is always useful for information about where to purchase all the necessary materials and tools for felting. Below are tables that specify the sales points for felting, wool in Moscow and St. Petersburg. You will find everything you need to felting in the stores presented in the tables.

Online shops